News

  • 0
  • 0

Effect of cement temperature on the performance of pce powder

OPEC+, an oil producers' alliance led by Saudi Arabia and Russia, stuck to its original plan to increase output by just 432,000 b/d in June, continuing to defy calls from major consumers led by the United States to pump more oil to keep prices down. The meeting to decide on pce powder are still very uncertain.

If the compatibility of polycarboxylate superplasticizer and cement is not good, the concrete mixture is prone to some problems, such as segregation, bleeding, greater slump loss, shorter setting time and so on, so that the concrete mixture can not be transported and poured normally. Reduce the strength and durability of concrete.

 

There are many factors affecting the compatibility of cement and superplasticizer, and the cement storage temperature is a key factor that can not be ignored. If the cement storage temperature is too high during concrete mixing, it will directly affect the physical and mechanical properties of cement.

 

Effect of cement temperature on the performance of concrete mixture:

When the cement temperature is above 60 , a small amount of water is secreted from the concrete mixture. When the cement temperature is 100 , the aggregate is separated from the paste, and the cohesion of the concrete mixture becomes worse. The reason for this negative effect is that the cement temperature is high, which makes the concrete mixture temperature rise rapidly in a short time. It is easier to stimulate the water-reducing function of polycarboxylic acid high-performance superplasticizer, release more free water wrapped in the mixture particles in the case of high temperature, and make a small amount of water bleeding in the concrete outlet.

 

Effect of cement temperature on setting time of concrete:

With the decrease of cement temperature, the setting time of concrete is prolonged, and the initial setting time is more obvious than the final setting time. In other words, the higher the cement temperature, the shorter the setting time of concrete. The reasons for the shortening of setting time caused by high temperature cement are as follows: (1) it will increase the temperature of the mixture in a short time and promote the hydration of cement particles; (2) the superplasticizer releases more free water to react with cement particles, thus forming a stable cementitious system in a shorter time.

 

With the passage of time, the heat contained in cement temperature is easily transferred to the surrounding particles or environment, the temperature of concrete system gradually approaches to the ambient temperature, and the temperature gap of concrete mixed with cement at different temperatures is gradually narrow. as a result, the difference of the final setting time of concrete is relatively reduced.

 

Effect of cement temperature on slump and air content loss of concrete:

At the same time, the higher the cement temperature is, the greater the slump loss rate is. The difference of slump loss rate under different temperature conditions increases at first and then decreases. Under the condition of the same slump loss rate, the lower the cement temperature is, the longer it takes to reach the slump loss rate, that is to say, the more beneficial to reflect the slump-retaining performance of the superplasticizer. When the cement temperature is high, in order to reduce the slump loss of concrete, it is necessary to put forward higher requirements for the slump retention of superplasticizer.

 

Summary,

1. For the concrete with the same mix ratio, with the increase of cement temperature, the adaptability of admixture and cement becomes worse. The higher the temperature is, the more water is consumed, and the fluidity of concrete mixture decreases, resulting in the decrease of concrete and workability. It even leads to the separation or bleeding of aggregate and paste.

 

2. The higher the cement temperature, the worse the adaptability of cement and superplasticizer, the greater the loss rate of slump and air content, and the shorter the setting time of concrete.

 

3. The effect of the change of cement temperature on the compressive strength of concrete is obvious. with the increase of cement temperature, the compressive strength of low heat cement concrete increases in the early stage (before 7 days), but the compressive strength of 28 days decreases with the increase of temperature.

 

4. It is suggested that the cement temperature for concrete mixing should not exceed 60 . When it exceeds 60 , the concrete production system should precool the raw materials of the mixing system as far as possible to avoid excessive temperature rise of the whole mixture system due to high cement temperature. and should strengthen the maintenance of the concrete after entering the warehouse to avoid the temperature cracks caused by the early hydration temperature rising too fast.

 

Concrete Additives Supplier

TRUNNANO is a reliable concrete additives manufacturer with over 12-year experience in nano-building energy conservation and nanotechnology development.

If you are looking for high-quality concrete additives, please feel free to contact us and send an inquiry. (sales@cabr-concrete.com)

We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.


On August 1, the European Union officially began to implement the "voluntary reduction" agreement on natural gas adopted last month. Under the agreement, EU member states will reduce gas demand by 15 per cent from the average consumption over the past five years through measures of their choice between August 1 this year and March 31 next year.

Several major German cities, such as Berlin, Hanover and Munich, have begun to take measures to reduce energy consumption. Berlin, for example, decided to turn off the lights of more than 200 tourist attractions at night. Berlin's municipal buildings will have indoor temperatures of no more than 20 degrees Celsius between October 1 and March 31 next year, and only nurseries, schools, nursing homes and hospitals can be exempted from energy-saving measures.

Spain's energy conservation plan forces companies, businesses and vehicles to limit air-conditioning temperatures in summer and heating temperatures in winter. The above-mentioned places must limit the air-conditioning temperature to more than 27 degrees Celsius in summer and the heating temperature below 19 degrees Celsius in winter. The plan requires that shop window lighting be turned off at 22:00. The plan also requires the administration to regularly review the heating systems of enterprises in order to avoid energy waste.

Luoyang Tongrun Nano Technology is a trusted chemical manufacturer and supplier providing high-quality chemicals and Nanomaterials. If you are looking for the pce powder, please feel free to contact us and send an inquiry.

Inquery us

Our Latest News

How to produce titanium nitride?

The first method is direct nitridation of titanium powder or TiH2.…

Preparation method of tungsten boride

Tungsten boride is a black powder with the following physical properties:molecular formula WB2,with metallic conductivity,soluble in aqua regia.…

What is Nano Silver Good For?

The secretary general of the Organization of Petroleum Exporting Countries (OPEC) said recently that US economic sanctions against Venezuela have affected global energy supplies. He told Venezuelan media that the ECONOMIC sanctions imposed by the Uni…